www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 860c smd - 6 m arking ? hdf6834 prepared checked approv ed ? d a t e 200 6 - 5 - 11 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . mo dify content ? remark
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 3 of 8 1. package dimension 2. marking hdf 6834 hd: brand f : filter 6 : smd - 6 834 : no.
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 4 of 8 3.performance 3.1application low - loss saw filter of cordless system. center frequency: 860.5 mhz 3.2maximum rating operation temperature range - 4 0 to + 85 storage temperature range - 4 5 to +85 dc. permissive voltage 0 v dc. max. maximum input po wer 0 dbm 3.3 electronic characteristics item specification center frequency(fo) 860.5 mhz insertion loss(db) 1.) 851.00~870.00 mhz 2.)60 . 0~ 806.00 mhz 3.) 933.00 mhz 4.) 960.00~1200.00 mhz 4.5 db max 40 db min 40 db min 37 db min ripple deviation (fo 9 mh z)(db) 2.0 max input/output impedance(nominal) 50 3.4 frequency characteristics
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 5 of 8 3.5 test circuit 4. environmental characteristics 4 - 1 high temperature exposure subject the device to +85 for 16 hours. then release the filter into the room conditions for 24 hours prior to the m easurement. it shall fulfill the specifications in 3.3 . 4 - 2 low temperature exposure su bject the device to - 4 0 for 16 hours. then release the device into the room conditions for 24 hours prio r to the measurement. it shall fulfill the specifications in 3.3 . 4 - 3 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +8 5 for 30 minutes. then release the device into the room conditions for 24 hours prior to the me a surement. it shall meet th e specifications in 3.3 . 4 - 4 resistance to solder heat dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for 10 1 sec. then release the device into the room conditions for 4 hours. the device shall meet the specifications i n 3.3 . 4 - 5 solderability subject the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the terminals must be covered with new solder. it shall meet the specifications in 3.3 . 4 - 6 mechanical shock drop the device randoml y onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 3.3 . 4 - 7 vibration subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the devic e shal l fulfill the specifications in 3.3 .
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 6 of 8 5. remark 5.1 static voltage static voltage between signal load & ground may cause deterioration &destruction of the component. please avoid static voltage. 5.2 ultrasonic cleaning ultrasonic vibratio n may cause deterioration & dest ruction of the component. please avoid ultrasonic cleaning 5.3 soldering only leads of component may be soldered . please avoid soldering another part of component. 6 . packing 6 .1 dimensions (1) carrier tape: figur e 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 6 .2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 6 .3 taping structure (1) the tape shall be wound around th e reel in the direction shown below. (2) label device name user product name quantity lot no.
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 7 of 8 (3) leader part and vacant position specifications. 7 . tape specifications 7 .1 tensile strength of carrier tape: 4.4n/mm width 7 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm]
saw filter hdf 860c s - 6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916 881 e - mail: info@shoulder.cn page 8 of 8 w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0 .10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [figure 2] [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
